EMODnet Seabed Habitats

Title Copyright or Terms of Use
Broad Habitat - Deep Sea Habitats (EUSeaMap2 - EUNIS) - September 2016

The 2016 EUSeaMap2, produced by EMODnet Seabed Habitats was produced using a "top-down" modelling approach using classified habitat descriptors to determine a final output habitat.  Habitat descriptors (excepting Substrate) are calculated using underlying physical data and thresholds derived from statistical analyses or expert judgement on known conditions. The model is produced in Arc Model Builder (10.1). For more information on the modelling process please read the EMODnet Seabed Habitats. The model was created using raster input layers with a cell size of 0.002dd (roughly 250 meters). The model includes the sublittoral zone only; due to the high variability of the littoral zone, a lack of detailed substrate data and the resolution of the model, it is difficult to predict littoral habitats at this scale. The map follows the EUNIS 2007-11 classification system where it is appropriate.

This layer depicts the Deep Sea Habitats derived from the EUSeaMap2. These are habitats occurring beyond the continental shelf break at depths typically greater than around 200m. Knowledge of these habitats is very patchy and limited but is growing all the time, revealing more and more about the rich diversity of life found in the deep waters off Scotland.

Please cite EMODnet seabed habitats when using these data or products.

Information contained here has been derived from data that is made available under the European Marine Observation Data Network (EMODnet) Seabed Habitats project (www.emodnet-seabedhabitats.eu), funded by the European Commission’s Directorate-General for Maritime Affairs and Fisheries (DG MARE).

The Data Owner and EMODnet Seabed Habitats consortium accept no liability for the use of this data or for any further analysis or interpretation of the data.

Broad Habitat - Subtidal Sediment (EUSeaMap2 - EUNIS) - September 2016

The 2016 EUSeaMap2, produced by EMODnet Seabed Habitats was produced using a "top-down" modelling approach using classified habitat descriptors to determine a final output habitat.  Habitat descriptors (excepting Substrate) are calculated using underlying physical data and thresholds derived from statistical analyses or expert judgement on known conditions. The model is produced in Arc Model Builder (10.1). For more information on the modelling process please read the EMODnet Seabed Habitats. The model was created using raster input layers with a cell size of 0.002dd (roughly 250 meters). The model includes the sublittoral zone only; due to the high variability of the littoral zone, a lack of detailed substrate data and the resolution of the model, it is difficult to predict littoral habitats at this scale. The map follows the EUNIS 2007-11 classification system where it is appropriate.

This layer depicts the Subtidal Sediment  Habitats derived from the EUSeaMap2. Inshore subtidal sediments include shingle, gravel, sand and mud extending to the depth at which there is no effect from waves, typically around 50-70m. The shelf sediments extend to around 200m depth. Inshore subtidal sediments also include lagoons and maerl, a red seaweed with a hard chalky skeleton that forms small twig-like nodules which accumulate to form loosely interlocking beds, creating the ideal habitat for a diverse community of organisms.

Please cite EMODnet seabed habitats when using these data or products.

Information contained here has been derived from data that is made available under the European Marine Observation Data Network (EMODnet) Seabed Habitats project (www.emodnet-seabedhabitats.eu), funded by the European Commission’s Directorate-General for Maritime Affairs and Fisheries (DG MARE).

The Data Owner and EMODnet Seabed Habitats consortium accept no liability for the use of this data or for any further analysis or interpretation of the data.

Broad Habitat - Subtidal Rock (EUSeaMap2 - EUNIS) - September 2016

The 2016 EUSeaMap2, produced by EMODnet Seabed Habitats was produced using a "top-down" modelling approach using classified habitat descriptors to determine a final output habitat.  Habitat descriptors (excepting Substrate) are calculated using underlying physical data and thresholds derived from statistical analyses or expert judgement on known conditions. The model is produced in Arc Model Builder (10.1). For more information on the modelling process please read the EMODnet Seabed Habitats. The model was created using raster input layers with a cell size of 0.002dd (roughly 250 meters). The model includes the sublittoral zone only; due to the high variability of the littoral zone, a lack of detailed substrate data and the resolution of the model, it is difficult to predict littoral habitats at this scale. The map follows the EUNIS 2007-11 classification system where it is appropriate.

This layer depicts the Subtidal Rock Habitats derived from the EUSeaMap2. Subtidal rock habitats comprise bedrock, boulders and cobbles occurring below low water mark. The communities found here are strongly affected by the availability of light; shallow areas are typically dominated by seaweeds and in deeper areas below the photic zone (about 50m) communities comprise exclusively animals. Other factors influence the composition of communities including wave action, tidal stream strength and salinity.

Please cite EMODnet seabed habitats when using these data or products.

Information contained here has been derived from data that is made available under the European Marine Observation Data Network (EMODnet) Seabed Habitats project (www.emodnet-seabedhabitats.eu), funded by the European Commission’s Directorate-General for Maritime Affairs and Fisheries (DG MARE).

The Data Owner and EMODnet Seabed Habitats consortium accept no liability for the use of this data or for any further analysis or interpretation of the data.

Broad Habitat - Broad-Scale Predictive Habitat Map (EUSeaMap2 - EUNIS) - September 2016

Output of the 2016 EUSeaMap broad-scale predictive model, produced by EMODnet Seabed Habitats. The extent of the mapped area includes the Mediterranean Sea, Black Sea, Baltic Sea, and areas of the North Eastern Atlantic extending from the Canary Islands in the south to Norway in the North. The map was produced using a "top-down" modelling approach using classified habitat descriptors to determine a final output habitat. Habitat descriptors differ per region but include: Biological zone Energy class Oxygen regime Salinity regime Seabed Substrate Riverine input Habitat descriptors (excepting Substrate) are calculated using underlying physical data and thresholds derived from statistical analyses or expert judgement on known conditions. The model is produced in Arc Model Builder (10.1). For more information on the modelling process please read the EMODnet Seabed Habitats The model was created using raster input layers with a cell size of 0.002dd (roughly 250 meters). The model includes the sublittoral zone only; due to the high variability of the littoral zone, a lack of detailed substrate data and the resolution of the model, it is difficult to predict littoral habitats at this scale. The map follows the EUNIS 2007-11 classification system where it is appropriate.

This version is clipped to the Scottish zone, with an extension to continental shelf limits west of Rockall.  Please cite EMODnet seabed habitats when using these data or products.

Information contained here has been derived from data that is made available under the European Marine Observation Data Network (EMODnet) Seabed Habitats project (www.emodnet-seabedhabitats.eu), funded by the European Commission’s Directorate-General for Maritime Affairs and Fisheries (DG MARE).

The Data Owner and EMODnet Seabed Habitats consortium accept no liability for the use of this data or for any further analysis or interpretation of the data.